Manufacture

EMIOTEST 3114 - Gravimetric dust meter
Information card

Automatic dust meter EMIOTEST 3114, in its innovative technical solution, is a portable device designed to perform, in closed channels, periodic measurements of dust concentration in the flue gases and a dust mass stream (e.g. in the exhaust) to define the emission of dust into the atmosphere. The measurement method is based on the isokinetic collection of gas partial flow and separating collected particulate matter on the filter material. The measurement can be performed on either the inner or the outer filter.

Extensive equipment, exterior, dust meter kit also allows for independent measurement of volume flow of gas in the test channel and independent measurement of gas humidity. Technical equipments solutions, algorithm controlling measurement and calculations are in accordance with the applicable standards: national standard PN-Z-04030-7, PN-EN-13284-1 and ISO 9096.

Device

Digital Flowmeter DFM2006
Information card

This is a new solution for a series of devices manufactured by EMIO used for measurement of flow rate of gases in the closed channels. As in the DFM 1194/1197 flowmeters, the operation of the DFM 2006 flowmeter is based on micromanometric differential pressure measurement.

The flow meter is equipped with its own temperature probe and may be also equipped with a probe for moisture content of the gas measurement. It can be used with all kinds of pitot tubes for which constant K has been defined.

The device is particularly used for determining the velocity profile of the gas in the duct by registering the dynamic pressure distribution in the test section. The application program that supports work of the flowmeter performs ongoing calculations of the gas velocity in the duct. Final results are presented in the form of a report which contains calculated values ‚Äč of the gas stream referenced to the actual and contractual conditions for dry and wet gas.

Flowmeter DFM 2006 is designed for environmental services in power plants, CHP plants, ironworks, large industrial plants, and also for environmental inspectorates or in laboratory measurements of gas flow in closed pipe ducts equipped with any type of orifice measurement.

Calculation algorithm of gas volume flow is consistent with the recommendations of PN-Z-04030-7:1994 (ISO 9096:1992) and PN-EN 13294.

Device

EAS-2
Information card

Aspirator EAS-2 is a portable device. It is designed to collect on tubes or sorption scrubbers gas samples that come from technological processes or technical operations. Determination of the concentration of substances in samples taken is carried out in a research laboratory.

The elements and components of the aspirators control unit are positioned both inside and outside of the housing.

On the side plate placed are two-section aerosol filters and a socket with power switch. Additional slot separated for each channel are used to connect the temperature probe of the sucked gas stream exiting scrubber/sorption tubes. Alternatively in one of these nests user may attach sensor measuring ambient temperature nearby device.

On the upper plate, separately for each channel are located:
  • display (16 lines, 21 columns)
  • indicator lights signaling:
    • warm-up stare of gas aspiration track "HEAT";
    • working state of pump "PUMP"
    • working state of aspirator "SERVICE"
  • button "MENU" to navigate trough lines and columns
  • button "WART" to set values ascending/descending
  • buttons "ENTER/Start"
  • buttons "ESC/Stop"
  • buttons to adjust the contrast of the display
  • slot for serial connector "RS232C" to connect a PC or serial printer
Inside the housing placed are distinct for each channel following elements:
  • heated aspiration track, which task is to prevent out dropping water vapor in the measuring section
  • set measuring pressure, temperature and humidity of aspirated gas
  • flow measurement module
  • set of control valves
  • rotary aspiration pump
  • electronics module

Device

CMWT 2007 - Digital meter for measurement of relative humidity and temperature of gas in channel
Information card

CMWT-2007 digital meter is designed for direct measurement of relative humidity and temperature of the gas in ducts, under conditions without presence of condensate and soot. The device allows the registration and calculation of gas humidity degree X and carries out measurement reports. Data can be also transfered to computer.

Device

ZPPW set for sempling coal dust from dust-gas ducts (additional set for dustmeter Emiotest 3114)
Information card

Set is used to collect a representative sample of coal dust from dust-gas ducts by isokinetic method, to determine its particle size distribution and moisture content. Sampling is carried out by using the isokinetic "zero" probe. Set is prepared for cooperation with a control unit 3114 of the dust meter EMIOTEST or a control unit 2598 of the dust meter EMIOTEST and type AZ-15 suction unit. Special software dust meter, the shape and dimensions of the probes are compatible with PN-91/M-34131 "Installations mills. Sampling of dust".

Device

One-piece velocity aspiration probes
Information card

Device

Cooled aspiration probe SA-kw type, to collect samples for PAH determination
Information card

Device

Aspiration segmented unheated velocity probes
Information card

Device

Pitot tubes and pitot tubes heads
Information card

Device

Dust separators for internal filtration
Information card

Device

External heated-up dust separator
Information card

Device